desquamate

英

美

v.  剥落，脱落，脱皮

现在分词：desquamating　过去式：desquamated　第三人称单数：desquamates　过去分词：desquamated　

英英释义

verb

• peel off in scales
  1. dry skin desquamates
  Synonym:peel off

双语例句

• While above 600 ℃, the plating will lose its application properties due to desquamate.
  当温度超过600℃时，由于膜层产生剥落而失去使用性能。
• Methods A high speed vibration method using a fragment of glass was created to desquamate the flagellin of S. typhi, it could increase the yield of flagellin antigen. By two centrifuging steps, bacterial debris was removed, and the flagellin was collected.
  方法：创用玻璃渣高速振动法打脱细菌鞭毛，可提高鞭毛抗原得率，然后分二步离心去掉细菌，再收集鞭毛。
• On the condition of SRV wear, The predomination wear mechanisms of the products translate gradually from oxidation and abrasive wears to adhesion and desquamate with the increase of doped ZrC content.
  在微动磨损条件下，随着掺杂ZrC数量的增加，合成产物的主要磨损机制由粘着磨损、剥层磨损、氧化磨损和磨粒磨损逐渐转化为以剥层磨损和粘着磨损为主。
• The phenomena and mechanism of desquamate are defined for the first time.
  首次提出了竹材切削过程表面剥落现象及机理。
• Objective To develop an in vitro culture system for Cryptosporidium parvum in Madin-Darby canine kidney ( MDCK) cell and observe its life cycle ( from desquamate to oocyst).
  目的建立微小隐孢子虫体外感染犬肾细胞（MDCK细胞）模型，并观察其生长发育过程。
• Results showed the type of ceramic layer's wears failure was affected by ceramic layer's thickness under this friction condition; while the ceramic layer would desquamate if its thickness was less than the critical numerical value.
  结果显示：在滚动摩擦条件下，陶瓷层失效形式受到其厚度的影响，当陶瓷层厚度小于临界厚度时，试样表面出现陶瓷层剥落现象。
• At 90(°) jet angles, the coatings present the fatigue desquamate due to the upright wallop of particles on the coating surface.
  在90（°）冲蚀磨损时，涂层的失效主要是垂直表面的磨粒冲击力导致涂层疲劳剥落。
• But under the dry condition the high frequency alternating heat stress is light, the coat desquamate slowly though a great deal little chap units is formed, the wearing performance of the TiN coat cutter is very good, the steady cutting time is long.
  与此相反，干式切削时，高频交变热应力较小，虽在涂层表面有微裂纹产生，但涂层不易剥落，刀具耐磨性较好，可进行长时间稳定切削。
• The desquamate disappears with the increase of the moisture content but spiny hair appears on the surface if the moisture content is too high.
  随着含水率的增加，表面剥落现象消失，但含水率过高，切削表面出现拉毛现象。
• No bubble, wrinkle or desquamate.
  不起泡，不起皱褶或者脱层。